Products
BSM and BSMK
| Rotary drive with electrical motor and gear. | ||
| Without hand crank: | BSM | |
| With hand crank: | BSMK | |
| Ratio: | 65:1, 100:1, 250:1, 450:1, 750:1 | |
| 1500:1, 2000:1, 2500:1, 4000:1 |
- Description
- Technical info
Drive assembly on left- or righthand side. Maximum feed per pump stroke of the plunger is equivalent to approx. 0.30 cm³. Feed is reduced approx. 0.05 cm³ for each anti-clockwise turn of the set screw. To ensure accurate adjustment, the set screw is stopped each 1/4-turn by a spring-loaded ball pressing into grooves in the set screw.
Turning the set screw a 1/4-turn thus reduces or increases the volume fed by approx. 0.012 cm³. We recommend not to adjust the set screw more than about 5 turns, a setting gives approx. 0.03 cm³ (one drop of oil) per stroke. You can check the feed by counting the number of drops passing the sight glass during one minute. Multiply this by 0.03 cm³ and you obtain an accurate output.
Technical information for B-lubricator
Noise level
The sound level is less than 70 dB (A)
Oils
The lubricator is capable of pumping oils and other fluids with a maximum viscosity of approx. 600 cSt at 40 °C. High viscosity oils and fluids may have to be pre-heated before they can be pumped.
Performance
| Plunger diameter 9 mm (standard) | |
| Max feed per pump stroke: | 0,30 cm³ |
| Max continuous back-pressure: | 12 MPa/1 700 psi |
| Max intermittent back pressure: | 30 MPa/4 400 psi |
| Plunger diameter 7 mm | |
| Max feed per pump stroke: | 0,18 cm³ |
| Max continuous back pressure: | 20 MPa/2 900 psi |
| Max continuous back pressure: | 30 MPa/4 400 psi |
Adjusting feed
Maximum feed per pump stroke of the plunger is equivalent to approx. 0.30 cm³. Feed is reduced approx. 0.05 cm³ for each anti-clockwise turn of the set screw. To ensure accurate adjustment, the set screw is stopped each 1/4-turn by a spring-loaded ball pressing into grooves in the set screw.
Turning the set screw a 1/4-turn thus reduces or increases the volume fed by approx. 0.012 cm³. We recommend not to adjust the set screw more than about 5 turns, a setting gives approx. 0.03 cm³ (one drop of oil) per stroke. You can check the feed by counting the number of drops passing the sight glass during one minute. Multiply this by 0.03 cm³ and you obtain an accurate output.
Motors
| Electrical data: | acc. to IEC 34 – 1. | |||||
| Manufacture: | Brook Crompton | |||||
| Isolation class: | F | |||||
| Protection class: | IP55 |
| Hz | Voltage code | ||
|---|---|---|---|
| Voltages: | 3 x 220-240/380-420 V | 50 Hz | 1 |
| 3 x 250-275/440-480 V | 60 Hz | 1 | |
| 3 x 500 V | 50 Hz | 2 | |
| 3 x 400/690 V | 50 Hz | 3 | |
| 3 x 575 V | 60 Hz | 4 | |
| Other* | 9 | ||
| Power rating: | 0.18 kW/1 370 rpm | 50 Hz | |
| 0.21 kW/1 680 rpm | 60 Hz | ||
| 0.25 kW/2 810 rpm | 50 Hz | ||
| 0.28 kW/3 370 rpm | 60 Hz |
Single screw gear, ratio 65:1, 100:1
Single screw gear, ratio 65:1, 100:1
*Motors of other makes, for other voltages, single-phase, operation with stand-by heating, Nema or CSA approval etc. are available on special request.
